S_FlickerRemoveMatteRemoves temporal flickering from the Source clip using a Matte clip to specify the area where the average brightness should remain constant. To use this effect, select a Source frame that has the desired brightness within the Matte, and hit the Set Hold Level button. When other frames are processed, their brightness will be scaled so the average brightness within the Matte is equal to the Hold Level. You can keyframe different Hold Level values over time to account for desirable brightness changes.In the Sapphire Time category.
Inputs:
|
|
Parameters:
-
Load Preset:
Push-button
.
Brings up the Preset Browser to browse all available presets for this effect.
-
Save Preset:
Push-button
.
Brings up the Preset Save dialog to save a preset for this effect.
-
Mocha:
Default:
0,
Range:
0 or greater.
Brings up the Mocha window for tracking footage and generating masks.
-
Blur Mocha:
Default:
0,
Range:
0 or greater.
Blurs the Mocha Mask by this amount before using. This can be used to soften the edges or quantization artifacts of the mask, and smooth out the time displacements.
-
Mocha Opacity:
Default:
1,
Range:
0 to 1.
Controls the strength of the Mocha mask. Lower values reduce the intensity of the effect.
-
Invert Mocha:
Check-box, Default:
off.
If enabled, the black and white of the Mocha Mask are inverted before applying the effect.
-
Resize Mocha:
Default:
1,
Range:
0 to 2.
Scales the Mocha Mask. 1.0 is the original size.
-
Resize Rel X:
Default:
1,
Range:
0 to 2.
The relative horizontal size of the Mocha Mask.
-
Resize Rel Y:
Default:
1,
Range:
0 to 2.
The relative vertical size of the Mocha Mask.
-
Shift Mocha:
X & Y, Default:
[0 0],
Range:
any.
Offsets the position of the Mocha Mask.
-
Bypass Mocha:
Check-box, Default:
off.
Ignore the Mocha Mask and apply the effect to the entire source clip.
-
Show Mocha Only:
Check-box, Default:
off.
Bypass the effect and show the Mocha Mask itself.
-
Combine Masks:
Popup menu, Default: Union
.
Determines how to combine the Mocha Mask and Input Mask when both are supplied to the effect.
-
Union:
Uses the area covered by both masks together.
- Intersect: Uses the area that overlaps between the two masks.
- Mocha Only: Ignore the Input Mask and only use the Mocha Mask.
- Intersect: Uses the area that overlaps between the two masks.
-
Union:
Uses the area covered by both masks together.
-
Set Hold Level:
Push-button
.
Pressing this button has a side effect of setting the Hold Level parameter to the average Source brightness within the Matte at the current frame. It causes the output to equal the Source at this frame. This button retains no value itself, and is turned back off immediately after being pushed. On AVX2, this button sets the value at the current time, creating a keyframe if necessary. On AVX1, it sets the value at all active keyframes. To animate the Hold Level on AVX1, you must create all the keyframes first, then set the value at each one separately.
-
Hold Level:
Default:
0.5,
Range:
0.01 or greater.
The requested average output brightness for the area within the Matte.
-
Matte Use:
Popup menu, Default: Luma
.
Determines how the Matte input channels are used to make a monochrome matte.
-
Luma:
the luminance of the RGB channels is used.
- Alpha: only the Alpha channel is used, or if there is no valid Alpha channel the Red channel is used.
- Alpha: only the Alpha channel is used, or if there is no valid Alpha channel the Red channel is used.
-
Luma:
the luminance of the RGB channels is used.
-
Invert Matte:
Check-box, Default:
off.
If enabled, the black and white of the matte are inverted before use.
See Also:
-
FlickerRmMatteColor
FlickerRemove
FlickerRemoveColor
FlickerMatch
FlickerMatchColor
FlickerMatchMatte
FlickerMchMatteColor
Flicker
Sapphire Plug-ins Introduction